• 商家新闻

  • 行业新闻

  • 行业新闻
  • 普通应如何保养KIC2019注册自助领取白菜呢
  • 成本站编辑:2019免费白菜网址大全设备有限公司通告日期:2019-09-12 14:21 浏览次数:
  •       1、在利用过程中轻拿轻放,切勿与其他硬物相互碰撞;避免内部IC脱落和破坏。

      

      2、在利用过程要小心KIC测试仪的洁净,避免一些杂物落入IC插槽,造成IC接触不良。

      

      3、在过炉时一定要套上隔热性能好的1/4inch厚的隔热套,避免在过炉时高温烤坏仪器;以及时常高温的烘烤,缩短了KIC的运用寿命。

      

      4、运用电池时,永恒要用碱性电池,避免在高温测试过程中出现电压不安定,造成曲线测试不完整。在转换电池时,要小心电池头与电池接触良好。

      

      5、运用时,请按照KIC专业的统考步骤(先与计算机进行报道->再过炉高考->末了下载曲线)开展测试。

      

      6、在开展下次温度曲线测试时,确保KIC测试仪内部温度低于35度,避免重蹈覆辙测试导致内部温度上升而损坏仪器。

      

      7、在插和队热电偶时,不要两个或两个以上的同时开展插和队,这样容易会造成KIC2019注册自助领取白菜通道的破坏。

      

      8、在利用中,请确保AirTC焊点完好,因为他不仅起到控制仪器开始与截止记录温度数据,而且还提供多少到仪器进行利率的测算,AirTC的接触不良将直接影响数据丢失、不完全。

    1. Handle with care during use and do not collide with other hard objects; Avoid internal IC shedding and damage.

    2. Pay attention to the cleaning of the KIC tester during use, and avoid some sundries falling into the IC slot, resulting in poor IC contact.

    3, in the furnace must be covered with heat insulation performance good 1/4inch thick heat insulation sleeve, avoid in the furnace when high temperature broiling instrument; And often high temperature baking, shortened the service life of KIC.

    4, when using the battery, must use alkaline battery, avoid in the high temperature test process voltage instability, resulting in incomplete curve test. When replacing the battery, pay attention to the good contact between the battery head and the battery.

    5, when using, please follow the KIC standard test steps (first communicate with the computer -> and then pass the furnace test -> and finally download the curve) to test.

    6. During the next temperature curve test, ensure that the internal temperature of the KIC tester is lower than 35 degrees, so as to avoid damaging the instrument due to the increase of internal temperature caused by repeated tests.

    7, in the plug and pull thermocouple, do not two or more at the same time to plug and pull, this will easily cause damage to the KIC furnace temperature tester channel.

    8. In use, please ensure that AirTC solder joint is in good condition, because it not only controls the beginning and end of recording temperature data of the instrument, but also provides data to the instrument for calculation of thermal efficiency. Bad contact of AirTC will directly affect data loss and incomplete.


    1. 
         
         
         
         
         
    2.     
    3.